Hydrolytic degradation and biodegradation of polylactic acid electrospun fibers.

Increased use of bioplastics, such as polylactic acid (PLA), helps in reducing greenhouse gas emissions, decreases energy consumption and lowers pollution, but its degradation efficiency has much room for improvement. The degradation rate of electrospun PLA fibers of varying diameters ranging from 0.15 to 1.33 µm is measured during hydrolytic degradation under different pH from 5.5 to 10, and during aerobic biodegradation in seawater supplemented with activated sewage sludge. In hydrolytic conditions, varying PLA fiber diameter had significant influence over percentage weight loss (W%L), where faster degradation was achieved for PLA fibers with smaller diameter. W%L was greatest for PLA-5 > PLA-12 > PLA-16 > PLA-20, with average W%L at 30.7%, 27.8%, 17.2% and 14.3% respectively. While different pH environment does not have a significant influence on PLA degradation, with W%L only slightly higher for basic environments. Similarly biodegradation displayed faster degradation for small diameter fibers with PLA-5 attaining the highest degree of biodegradation at 22.8% after 90 days. Hydrolytic degradation resulted in no significant structural change, while biodegradation resulted in significant hydroxyl end capping products on the PLA surface. Scanning electron microscopy (SEM) imaging of degraded PLA fibers showed a deteriorated morphology of PLA-5 and PLA-12 fibers with increased adhesion structures and irregularly shaped fibers, while a largely unmodified morphology for PLA-16 and PLA-20.

Advances in Cellulose-Based Composites for Energy Applications.

The various forms of cellulose-based materials possess high mechanical and thermal stabilities, as well as three-dimensional open network structures with high aspect ratios capable of incorporating other materials to produce composites for a wide range of applications. Being the most prevalent natural biopolymer on the Earth, cellulose has been used as a renewable replacement for many plastic and metal substrates, in order to diminish pollutant residues in the environment. As a result, the design and development of green technological applications of cellulose and its derivatives has become a key principle of ecological sustainability. Recently, cellulose-based mesoporous structures, flexible thin films, fibers, and three-dimensional networks have been developed for use as substrates in which conductive materials can be loaded for a wide range of energy conversion and energy conservation applications. The present article provides an overview of the recent advancements in the preparation of cellulose-based composites synthesized by combining metal/semiconductor nanoparticles, organic polymers, and metal-organic frameworks with cellulose. To begin, a brief review of cellulosic materials is given, with emphasis on their properties and processing methods. Further sections focus on the integration of cellulose-based flexible substrates or three-dimensional structures into energy conversion devices, such as photovoltaic solar cells, triboelectric generators, piezoelectric generators, thermoelectric generators, as well as sensors. The review also highlights the uses of cellulose-based composites in the separators, electrolytes, binders, and electrodes of energy conservation devices such as lithium-ion batteries. Moreover, the use of cellulose-based electrodes in water splitting for hydrogen generation is discussed. In the final section, we propose the underlying challenges and outlook for the field of cellulose-based composite materials.

Flexible Modulation of CO-Release Using Various Nuclearity of Metal Carbonyl Clusters on Graphene Oxide for Stroke Remediation.

Utilizing the size-dependent adsorption properties of ruthenium carbonyl clusters (Ru-carbon monoxide (CO)) onto graphene oxide (GO), a facile CO-release platform for in situ vasodilation as a treatment for stroke-related vascular diseases is developed. The rate and amount of formation of the CO-release-active RuII (CO)2 species can be modulated by a simple mixing procedure at room temperature. The subsequent thermally induced oxidation of RuII (CO)2 to RuO2 on the GO surface results in the release of CO. Further modulation of thermal and CO-release properties can be achieved via a hybridization of medium- and high-nuclearity of Ru-CO clusters that produces a RuO2 /RuII (CO)2 /6 Ru-CO-GO composite, where 6 Ru-CO-GO provides a photothermally activated reservoir of RuII (CO)2 species and the combined infrared absorption properties of GO and RuO2 provides photothermal response for in situ CO-release. The RuO2 /RuII (CO)2 /6 Ru-CO-GO composite does not produce any cytotoxicity and the efficacy of the composite is further demonstrated in a cortical photothrombotic ischemia rat model.

A rapid and highly sensitive strain-effect graphene-based bio-sensor for the detection of stroke and cancer bio-markers.

Here, we propose a highly sensitive and rapid bio-sensor for the detection of bio-markers for stroke and cancer-related diseases, based on the utilization of the adsorption properties of ruthenium carbonyl (Ru-CO) clusters on monolayer graphene (MG). A fast rate of decarbonylation of Ru-CO to form ruthenium oxide nanoparticles (RuO2 NPs) on MG was observed. The quantitative detection of matrix metalloproteinase-2 (MMP-2) (bio-marker for stroke and vascular diseases) was demonstrated by tracking the spectral shift of the characteristic G band of graphene caused by the adsorption of RuO2 NPs. A concentration as low as 17 ng mL-1 of MMP-2 was detected in a simulated clinical serum sample. This effective bio-sensor has the potential to revolutionize the biomedical field in the early detection and possible prevention of stroke and cancer diagnosis.